Jump to content

My head hurts (BT4Z-19G364-A)


Recommended Posts

Ok. I'm very sorry to start another remote start post but I've read and searched here til im about cross-eyed. I recently purchased this bi directional kit (BT4Z-19G364-A) for the wife's 2013 limited with no push button start and no powered lift gate. So, other than the hood switch, do I need anything else besides haveing it activated at the dealer? The kit says it doesn't include the PATS interface kit. Will I also need this? My apologies for the new thread but this is confusing! I put the short range kit on my f150 and it was a piece of cake! Thanks all.

  • Like 1
Link to comment
Share on other sites

I just ordered it. I was hoping to have all the parts needed ordered and received around the same time so I can just install it and go get it enabled. If it does end up needing the interface thing, I'm assuming it would have to be plugged into the remote start module and I'd like to only remove the rear cover once for the install.

Link to comment
Share on other sites

Yeah, I thought I was onto something earlier when I found that video. But it's for an aftermarket starter. The one I bought is an actual ford plug and play kit (part #BT4Z-19G364-A). Here's a link to one like the one I bought. I'm pretty sure it plugs into the tpms module behind the left rear panel. I'm just not sure if I need this PATS bypass thingy or not. Thanks for the video link though!

Link to comment
Share on other sites

I think we keep finding the same things,akirby! I've been all over the Internet and I'm starting to think I'm going to end up having to install what I get, have it activated,and try it. If it's a no go, I'll assume I need the interface kit. I'm almost thinking hopefully the interface kit is needed on the older models? I can't find out what constitutes needing to bypass the PATS system. I know this plug and play model is discontinued and ford has started selling these kits by the piece, so I guess that's why I can't find a definitive answer. I was just hoping maybe someone here had installed this kit on their similar Edge and could tell me how I find out if I need the interface kit or not. Thanks for helping me search though.

Link to comment
Share on other sites

I wanted to reply awhile ago, but, I couldn't log into the site for over a week!

Ā 

The kit you purchased (BT4Z-19G364-A) has everything you need (besides the hood switch, which you have).

Ā 

Everything can be installed at the rear drivers side interior quater panel. You can program the keys yourself (PATS), as long as you have two OEM keys available.

Ā 

The install should take under an hour. Instructions are here: http://www.fordservicecontent.com/ford_content/catalog/accessory_files/2011-2013%20Remote%20Access_Truck3-15-2013.pdf

Ā 

I have done a previous write up that should help clear thing up:http://www.fordedgeforum.com/topic/17035-adding-oem-remote-start-kits-parts-explained-detailed-2011/page-1

Ā 

The dealer can activate remote start for you (should be 30-60 minutes labor) via IDS or you can do it yourself with a Bluetooth OBD device and forscan.

Ā 

PM me with any questions, I'd be glad to help (or ask me publicly here as it may guide someone else attempting the same thing).

  • Like 2
Link to comment
Share on other sites

Thanks for the reply. I had bookmarked your post you linked. It was very helpful and informative! So looking at the install instructions you included,looks like I should have everything I need. I did have to buy the hood switch because for whatever reason, we didn't have one, just the wiring for it. So it looks like since I don't have the shock sensor or the cell phone start module, I just leave one end of the T harness loose and plug the other two ends to the tpms module and the remote start module. Thanks again for the reply and the links!

Link to comment
Share on other sites

Can you confirm the part number on the remote starter module?

Ā 

There is no difference between a VSS and an RMST module (both provide shock sensor functionality). In most kits, the part number is DL3J-19G367-AB.

Ā 

From the only google image I see when entering your kit part number, it appears as though your module MIGHT be part number BT4J-19G364-AA. It should still work, but that was the RMST module from the 2011 kit.

Ā 

It should work fine and either way you would connect the same:

Ā 

Disconnect TPM cable from TPM module. Insert adapter from t harness into TPM module (connect the aerial antenna, the long rectangular one, into the other port on the TPMs module), then insert the TPM cable you disconnected into the t-harness. Then finally the last plug in your t-harness goes into your RMST module (as does the long range antenna).

Ā 

Basically the t-harness sits between the TPMS module, its original cable and the remote starter module.

Ā 

All adapters on the t-harness will need to be used (don't leave any disconnected).

Edited by candurin
Link to comment
Share on other sites

Excellent! Thanks for all your help and reassurance. Like I said, I installed the short range kit (the one with the integrated key) on my f150,so I understand the whole getting it turned on and programmed at the dealer thing. This one just had me a little concerned with the "PATS interface kit not included" part in the ad. Wasn't sure if I was going to need that or not. So it's all wrapped up under the tree (Christmas gift for the better half),waiting to be installed next week. If I run into any issues, I'll be sure to post them for anyone maybe looking for some info. Thanks again!

Link to comment
Share on other sites

  • 2 weeks later...

Just wanted to follow up here. The starter is up and running. Super easy installation. I followed the post I found here by j3st3r with the step by step and pictures and it couldn't have been easier! Also thanks to candurin for his posts on what kits I needed to look for and for answering all my questions in this thread. Thanks guys!

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...