Jump to content

2.0 Ecoboost with small evap leak P0456.


Dave33

Recommended Posts

My daughter's car has code P0456 small evap leak. Doing some research most issues are with the purge valve however there is no such valve on the 2.0 turbo. There is a part called evap canister valve which is much more expensive than a normal purge valve. Has anyone experienced this with a possible fix. Thanks.

Link to comment
Share on other sites

Thanks for the reply and diagram. I guess it's called a canister vent solenoid and not a purge valve and It's about $100. I'll have to have the system smoked to see if I can find a leak. I don't want to throw parts at it at that price. If it were a $25 purge valve I would take the chance.

Link to comment
Share on other sites

  • 1 month later...

Edit: I had the vent solenoid valve or "purge valve" checked and it wasn't holding a vacuum. I replaced the valve which comes with all the hoses with an OEM from the dealership. All was fine for about 800 miles and the light came back on. I then cleaned the fuel filler door flap but again the light came back on after about 500 miles. Now I'm at a loss. I have also sprayed all connections with soapy water but have found nothing.

 

Anyone have any ideas or suggestions?

Edited by Dave33
Link to comment
Share on other sites

  • 2 months later...
  • 3 weeks later...

The part number for my car is BB5Z-9G271-B. Cost was around $90. It didn't fix the problem. CEL is still coming on so I'll probably take it to our local shop to be smoked. I'm not throwing any more money at until I know exactly what the problem is.

Edited by Dave33
Link to comment
Share on other sites

  • 7 months later...
On 5/4/2018 at 6:24 AM, WWWPerfA_ZN0W said:

There is a purge valve I think, but Ford probably lists it as a "hose assembly". Seen that a LOT lately. On the 3.5 EB, you can actually find the purge valve as a separate part. But on smaller engines, assemblies are much more common.

post-23566-0-29679300-1525440341_thumb.jpg

 

Is this diagram valid for the 2015 2.0L model? 

 

Also, if you remove this Valve... Can you do the mouth blow test? :)

Edited by 2011edgese
Link to comment
Share on other sites

  • 2 weeks later...
On 5/5/2019 at 2:24 PM, 2011edgese said:

Dave... Mines just got this code. Did you ever get it fixed? I have the 2015 ecoboost model. 

No not yet. It stayed off all winter but now that the warmer weather is here it's on almost all the time. I'm thinking it may be the filler neck or capless fill port. I'll be making an appointment soon to have it smoked because the inspection is due in a couple of months.

  • Like 1
Link to comment
Share on other sites

  • 2 years later...
  • 7 months later...

Hi everyone, I own a 2016 ford edge eco boost. Ive ben noticing lately after i fill my tank of gas up that if i come to a red light or stop that the rpms flutter down than back up. Almost like a stutter. It only seems to happen after filling my gas up. I don't fill it all the way up but about 3/4. It’s frustrating because i cant find the problem. No check engine light on yet. The rpm fluctuations go away after driving a few miles but will happen next time i fill up. Any ideas??? 

 

 

  • Confused 1
Link to comment
Share on other sites

  • 2 weeks later...

Hey guys noticed my 2016 Ford Edge 2.0 Ecoboost has a bit of a rough idle right after I fill up with  gas. Once I drive it and it is idling the rough idle is gone.  There are no check engine lights present.    I have read up that it might be purge valve. But doesn’t want to just replace it if it might be something else.  Any ideas?  All thoughts are appreciated.  Also the best place to buy a purge valve if that is what is recommended. 
 

thank you. 

Link to comment
Share on other sites

  • 1004ron changed the title to 2.0 Ecoboost with small evap leak P0456.
48 minutes ago, Johnny G said:

Hey guys noticed my 2016 Ford Edge 2.0 Ecoboost has a bit of a rough idle right after I fill up with  gas. Once I drive it and it is idling the rough idle is gone.  There are no check engine lights present.    I have read up that it might be purge valve. But doesn’t want to just replace it if it might be something else.  Any ideas?  All thoughts are appreciated.  Also the best place to buy a purge valve if that is what is recommended. 
 

thank you. 

That is a symptom of a bad evap valve.

 

What did you use to read the stored/pending error codes? - the first OBDII device I used did not show any codes, then when I got the OBDLink MX it showed an evap pending code.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...