Search the Community

Hello all! I am having an issue with my 2014 Ford Edge SEL 3.5L. Currently the HVAC system blows air in the far left driver vent above the headlight control knob and the far right passenger vent, however, the middle vents (above the Ford Sync Display) are not blowing air, regardless of temperature or mode setting. I suspect this might have something to do with the mode door actuator, however, I am not entirely sure nor do I know where the mode door actuator is located. Please let me know if you have any ideas and let me know if I should include any more information. Thanks

Got rid of the corrosive orange and went with the Peak 10X. Why? Because Ford put out documentation to flush it out and replace it with yellow.

Hi guys recently got a 2013 edge limited with 60,000km. When you manual start (push start) the HVAC blower blows on full blast and the sync screen is black meanwhile on the right gauge cluster display it says "temporarily lost connection with touch screen". One you hit the power button on the stereo the screen turns on and everything works as normal. When you remote start the vehicle the screen stays black, no HVAC at all, no heated seats, nothing. And yes in the instrument panel all remote settings are set to auto and it is -20°C here. Also noticed when you open the car door when it is off the sync screen doesn't like off. It's like it's not getting a power signal without manually turning it on. Also not sure if this affects anything but the door keypad also doesn't work, I think the 7/8 button is stuck in as all keys are unresponsive and don't light up the keypad except for the 9/0 key which by pressing it, it will lock the doors without even hitting the 7/8 key. I've been trying to use forscan to figure out the issue but I only find f150 or super duty forscan pages. Only DTC on forscan is on the HVAC Module and says lost connection with BCM. Any suggestions?

I had a problem where my 2014 edge se would not switch from cold to heat. I changed the blend door but that did not fix it then I found you guys and watched a video here how to reset the hvac control module by pressing buttons on the heat control panel and that worked so thank you very much forum members. My problem is I have had to reset it about 3 more times since so my question is is there a permanent fix and how many times can you reset it before it doesn’t work anymore?

I have a couple of annoying issues with the heating system on my 2011 Mkx. Hoping someone with Mkx or Edge can confirm if this is normal behaviour. 1) When HVAC system is set to auto, the air only blows from the lower vents and never from the top so my feet end up being way too hot and upper body is cold. Not sure if this is by design or malfunction 2) Outside air temp displayed is off by 10-15 degrees Celsius after engine starts. Temps outside will be around -5 degrees Celsius but display will show around +8 to 10 degrees Celsius after engine start. It will drop a degree or so every minute and after about 5 minutes of driving will drop to actual outside air temp. This causes remote start to not engage the heater or the heated seat, steering wheel automatically. Not sure if this requires firmware update to fix this or if senor is faulty. Would appreciate if someone can let me know if this is normal or not since this is my first winter with the vehicle and the two behaviour above seems odd to me. I have a couple of annoying issues with the heating system on my 2011 Mkx. Hoping someone with Mkx or Edge can confirm if this is normal behaviour. 1) When HVAC system is set to auto, the air only blows from the lower vents and never from the top so my feet end up being way too hot and upper body is cold. Not sure if this is by design or malfunction 2) Outside air temp displayed is off by 10-15 degrees Celsius after engine starts. Temps outside will be around -5 degrees Celsius but display will show around +8 to 10 degrees Celsius after engine start. It will drop a degree or so every minute and after about 5 minutes of driving will drop to actual outside air temp. This causes remote start to not engage the heater or the heated seat, steering wheel automatically. Not sure if this requires firmware update to fix this or if senor is faulty. Would appreciate if someone can let me know if this is normal or not since this is my first winter with the vehicle and the two behaviour above seems odd to me.