my2k2zx2

I replaced mine in April, (see post above) and have not had the wrench icon show up once.  It was coming on almost every time I was driving before it was replaced.

I just got done replacing my 2016 2.0 throttle body.  We were getting a wrench icon with a "see owners manual" message constantly.  I did not get a code reading with my scanner.  Seems that was common with F150 models with the wrench icon.

This is the one that I bought on ebay.

https://www.ebay.com/itm/144902748645

The vehicle is a lot more responsive and the wrench icon has not come back.

The T50 I had was loose to begin with, was afraid it would fully strip out.  The TP50 I had fit much better.  Knowing that I'm doing it again in the spring I figured it would be easy to replace the plugs at that time.

What is the part # for replacement drain plugs?  I have a 2016 2.0 and had a heck of a time getting them out.  I did use a Torx Plus bit but damaged them a bit with the torque needed to break them free.

I'd like to replace them when I change the fluid again in the sprint.

I got this letter yesterday.  Now to figure out which dealership to go with for scheduling the appointment.

Took me about 45 minutes to install on our 2016.  JLT sent me the wrong kind of hoses so I had to redo the whole setup.  If you do get their kit, make sure you get "Gates Barricade" or you will have severe fuel vapors enter the cabin while driving.

I have an Edge with the 2.0 but went through this issue with my JLT install back in November.  They sent me the hoses that the gas fumes easily go through, after 100 miles the cabin air is thick with oil/fuel vapors.

I contacted them and they said they would send replacement hoses, but while waiting for them to arrive I went to town and bought some Gates Barricade hoses.  The temps were going to drop too far to work on the vehicle when the replacement hoses would arrive.

That was done in December and so far we have not had the fume issue come back.

I had this code last year in our 2016 2.0.  I replaced the plugs but it did not clear the code.  I moved the coils around and the code moved as well.  I bought a used coil and the code has yet to return.

It is that easy.  There is room to get it out after removing that lower bracket off.  You can remove the air filter box for more room but is completely optional.

I followed this and there was plenty of room to access the drain & fill plugs.  

T50 is quite loose, TP50 is the correct size.  My 3/8 ratchet did not provide leverage to get either plug to budge.  It's snowing now so I'll have to revisit this when it's warmer.

I was using this guide and ours had the exact setup.  Just could not get the drain plugs to budge.

I tried to change the PTU fluid on our 2016 today but I could not get either drain plug to budge with my basic 3/8 ratchet.  I'm hoping to get it loose after I get a longer ratchet.

We have an aftermarket (fortin) remote start that uses the factory fob.  We go lock-unlock-lock and the vehile starts up.  We did have a CEL come on last year and the remote start would not work until the issue was fixed and the code was cleared.

H7 does fit, put one in our 2016 earlier this year.  I removed the air filter box lid and moved the ground wire out of the way to install.  I did not have to remove the cowling to fit.   The battery tray has threaded holes for 3 different sized batteries, but is not mentioned in any documentation.  If you look up the battery on parts.ford.com it shows 90T5, H6 and H7 as compatible options.  I found that after the parts store in town only showed the stock battery size and it was special order only.

https://imgur.com/EFRbtXS

Last week I was getting a P0036 code, so I replaced the oxygen sensor.  This week I'm now getting a P0330 code, knock sensor 2.  Is this something that I can fix on my own or would I be better off taking it in to be replaced?  Or is there something else that can be done to take care of this issue?

Yeah, I think that's what I'm looking at for the drain.  How easy is it to remove the intake tube?  Or would it be enough to cover things with foil while I'm doing the drain/refill?

https://imgur.com/GEndJjW

I'm planning on changing the PTU fluid.  What I'm seeing doesn't look like anything I've seen on other Edge PTU.  The ones that I've seen had the fill and drain on the same side.

I think mine has the fill on the side and the drain on the bottom and both appear to need a T50 to remove.  Would that be the correct fill & drain plugs?