Xtra

I tried to look up the Turbo Tech Racing RMM, and found nothing for the Edge. I am interested because at some point my aftermarket RMM might fail as well. Please keep us informed on this project, what you find out could help me in the future. 

That RMM is Toast! Way better than just a photo. Thanks.for posting

16 minutes ago, Nick Halstead said:

Today put her up in the air and just as suspected. Ultimate Performance Rear Motor Mount is toast! Does have about 75,000 miles on it and is like 6 years old with lots of hard FWD launches.

 

First..\

First... Love that lift!! I have often thought of investing in one. Second, how about a photo of the damaged RMM as several of us here have these, including me. I am interested in seeing the carnage..

You have a good description of the exhaust system. Twin cats into the Resonanter, then two 2 1/4 inch pipes into the suitcase muffler at the back. Lots of Resonanter delete options are available. . 

23 hours ago, Ford4Life951 said:

this 4.8mb max upload sucks. all my photos are in that range or above haha

Nice ride, thanks for the photo. All you have to do is resize the photos and the site works great. 

How about a couple good photos. It sounds like it is a nice ride.?

On 10/1/2023 at 3:00 AM, WWWPerfA_ZN0W said:

are we seeing the end of an era? i sure hope not! but you know you have a sizeable fan following, so keep creating!

Thanks so much for your support over the years. Though I have ideas of what I would like to do next. I doubt that it will happen. 

I am sold out of the V3 CAI. I have quit making them for now.  There is still one remaining Ram Air V2 in carbon fiber. PM me for more info. 

I want to thank all of you for your support and positive feedback. I hope that everyone enjoyed watching the development and implication of the V3 CAI. I decided to stop making them because of the high cost to make them. I have kept my price the same for years now. The pre-covid price is the same as now., but as everyone knows the price of everything has increased a lot in the last few years. I buy in bulk to save, and with this last batch I had to restock on a lot of the items. I posted a photo of a large pile of boxes that contained the parts needed to restock. As I have said in the past this is a hobby for me, and I am happy as long as it does not cost me anything to make them ....break even. But on this last run I lost money and it has become necessary to increase the price just to break even. As many now find the price of a V3 to be excessive, the cost of the V3 is just under $400, and I would have to increase the price to keep going , I have decoded to just stop and call it quits. When you add in the high cost of shipping and PayPals fees. It is just too much for me to ask for any price increase.. While aFee has improved their intake, the V3 with Aux Air is still the king and nothing out there outflows it. Sometimes it is best to stop when still on top.  

I have two remaining Carbon Fiber V2 Ram Air Intakes available at a discount. I will stop making the CF V2 for the same reason, the price of materials has increased too much to continue with them . I might continue with the ABS V2 as I can still maintain a good low price on them and keep them affordable. It depends upon the demand if I do another run of V2 or not.

Thanks again,

Xtra. 

Going out of business sale. There is one remaining V3 in stock ready to go. 
 

This is the last one that I will ever build. Everything is polished  even the rivets and clamps. PM me for more info. 
@ Below cost to make 

On 7/15/2023 at 6:38 PM, dabangsta said:

Luckily at home it was a more moderate 111 degrees, that 7 degrees makes a big difference.

OMG that's hot!!! 118 * @ 4 in the afternoon.

The correct size elbow came in and the Elbow Reducers are ready to weld and polish. 

On 7/4/2023 at 7:31 PM, Nick Halstead said:

BC Coilovers installed

 

I like it!!!...  Looking good.

One of the great advantages of coil overs is the adjustability. Ride height , rebound. different weight and type springs. You can fine tune your suspension with coil overs,  ride soft or firm,  ride high or low with  hundreds of combos. .  Most people use the coil overs to set the ride height, and lower the car.  But there is so much more that can be done. One of the better things that can be done no matter how you set it up is to weigh the car.  By using 4 car scales you can sit in the car and balance the car left to right and front to back. By adjusting the shocks you can add or remove weight on a tire.  It is standard practice on race cars to set them up this way, and is part of the alignment process. It makes a huge difference in how the car handles..  

Scales are available on Amazon from just over $100 for the budget minded to professional sets that cost over $1,000

I have been busy the last few weeks with charity work and now that the 4th is over , I am back to work on the V3 as promised. I ran into a glitch when cutting the Reducer Elbows. I was  shipped the wrong size 45* elbow and I did not realize it until I had made the first cut. Now I will have to reorder a new 45* elbow before I can proceed. 

The competed 30* elbow ready to weld.

I have made the adaptor rings for both Elbows and after I cut the 45* elbow I did a test fit..And this is what I saw. 

Not good, I did not need this setback as I already had to stop work for a few weeks. I thought that I would do the fab today and the welding and polishing tomorrow. Ship by Friday . Now after posting this I will reorder up the new Elbow, and finish after they arrive.  

More parts came in, as the finished V3’s went out.

Was able to get a couple V3 shipped today. The rest will go out later this week. 
Will be contacting the members receiving these later tonight or tomorrow with tracking and expected delivery date. 

Thanks I appreciate the props. And feel for your Lincoln lol. 

Final assembly of the V3 with Aux Air Intake  ready to install. 

Should be shipping by next Monday. 

Almost done, worked on some of the Mandrel Bent 6061 Aluminum Elbow Reducers today. 

As there are two Elbow Reducers per V3,  it takes me a few days to finish them all. 

VanDookie54 when these tires are done. Would you buy the same 295 X 35  R21size again or would you return to the stock 265  X 40 R21 size? 

Installing the Sensor Port and Lid Gasket. All that remains is fabrication of the 6061 Mandrel bent Aluminum Elbow Reducers.

Adding the Aux Air Intake to the V3 lid. Once the Aux Air Intake Port is installed, the next thing is to deal with the Sensor Port. 

This video is a bit out of order as this work was done before the Adaptor was finished. Once the saw was setup all the aluminum parts were cut on the same day.

Cutting the Aux Air Intake blanks to length from a tube of 6061 aluminum.

Fabrication of the hinge clip and installing it completes the V3 Adaptor. Working with Aluminum is is way different than ABS. Everything on the V3 CAI is rust proof ,it's built from Stainless Steel, Aluminum and ABS. Now that the Adaptor is complete it is time to work on the Lids and finish up the Aux Air Intake and Sensor port. 

This video shows the completion of the Adaptor. These little hinges take a lot of hand shaping, filling, polishing and time to get correct. The results are worth it

. 

2 hours ago, bscott94 said:

Installed B6 Springs and Struts and H&R lowering springs. It's not super low but way better

 

That is an awesome combo of suspension parts. Not only do they make the car look great you will be surprised how well it will turn corners now. If you live where there are any curvy, twisty roads you should go there and have some fun. The car will also be safer at highway speeds if you ever have to make an emergency lane change it will be up to the task.