Jump to content

Fully remove glovebox? 2019 Ford Edge ST


Recommended Posts

Hoping to get some help here- I’m hoping to fully remove the glovebox on my 2019 Ford Edge ST in order to run a power cord. I’m hoping to run it from the passenger side cigarette lighter over across the inside of the dashboard to the driver side where it plugs into an accessory. I have unclipped the top of the glovebox but see no way to fully detach the bottom of the glovebox and remove it from the vehicle. While not exactly ‘necessary’, it would make this installation so much easier. Appreciate any and all help anyone can provide!

  • Like 1
Link to comment
Share on other sites

Welcome to the Forum @Milo M!

 

To ensure your personal Health and Safety, because the Passenger Knee Bag is integral to the Glove Box assembly, please review and fulfill the Supplemental Restraint System depowering and repowering procedures...

 

From the 2019 Edge Workshop Manual...

 

 

warning.jpg  WARNING: The following procedure prescribes critical repair steps required for correct restraint system operation during a crash. Follow all notes and steps carefully. Failure to follow step instructions may result in incorrect operation of the restraint system and increases the risk of serious personal injury or death in a crash.

 

NOTE: Removal steps in this procedure may contain installation details.

  1. Depower the SRS .
    Refer to: Supplemental Restraint System (SRS) Depowering (501-20B Supplemental Restraint System, General Procedures)...

 

(This procedure is also attached below as a PDF document)

SupplementalRestraintSystem(SRS)Depowering-GeneralProcedures-2019EdgeWorkshopManual.thumb.jpg.d3c4a5d95affb20f562f0beac109900e.jpg

 

Removal

  1. Open the glove compartment.

image.png.9d1b536ecec4164c7e1cba88c1fa3c80.png

 

  1. Detach the glove compartment door damper.

image.png.bf67803431e0defdc6fa552cd819c8f6.png

 

 

  1. Push the tabs and release the glove compartment door.

image.png.436d3fd3a3da5bcb7f2966b165f02667.png

 

4

  1. Disconnect the electrical connectors.
  1. Remove the bolts.
    Torque: 35 lb.in (4 Nm)

     
  1. Remove the screws.
    Torque: 22 lb.in (2.5 Nm)

     
  1. Release the clips and remove the glove compartment.
    Use the General Equipment: Interior Trim Remover

image.png.097766c466f3c61f18ceeedbd92dcf67.png

 

(This procedure is also attached below as a PDF document)

SupplementalRestraintSystem(SRS)Repowering-GeneralProcedures-2019EdgeWorkshopManual.thumb.jpg.9f065584f1c6f7e91e11ee548f927a78.jpg

 

Good luck, and Work Safely!

 

Supplemental Restraint System (SRS) Depowering - General Procedures - 2019 Edge Workshop Manual.pdf Supplemental Restraint System (SRS) Repowering - General Procedures - 2019 Edge Workshop Manual.pdf

Edited by Haz
  • Like 3
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...