jmr061

17 hours ago, MadMike740 said:

 

sounds like a good place to start is replacing the rear washer relay. Thank you for the reply

Actually the wiring diagram shows it as a non serviceable part.  I agree with @enigma-2 after looking at the wiring diagram....check fuse 28 in the engine compartment . 

Fuse 28.pdf

Service Manual Operation Info:

The order guide shows it came only in 302A option package so those with 300A and 301A did not have it.

2 hours ago, PageDeb13 said:

2011 Ford Edge, my menu switches to settings then sound on its own. I have researched how to access the "hidden" diagnostic screem however cannot get it to come up. I did a hard reset as well. My back up camera quit working aprox a year after I bought it. Unfortinately could not afford the warranty.  I read about the 2013 update. How can I tell if my APM just needs an update or replaced?

The camera is a camera issue, not an APIM issue.  As for the display switching to different screens on its own...sounds like it is getting a touchscreen input which would mean there is pressure on the display or the display is bad.  Do you hear it beep when it does this?  What happens when you try to touch the screen to do something?  Probably not an APIM issue.

3 hours ago, Cossie said:

My VIN 2FMPK4AP6GBC29640
I cannot find any information about the frequency of the tire pressure system. I had a Ford Edge Sport (Bj 2016) imported from the USA to Germany. I have now put on winter tires, but with the local 433 MHz. Now the tire monitor reports that there is no pressure. However, I haven't learned the new tires yet because I don't know if I need 315 MHZ. If the 433 mhz are recognized, my next question, how do I learn these 4 tires to the BC? Thanks for a reply.

Your specific vehicle build info states 

•  Tire Pressure Sensors - 315 MHZ

it took me a bit to get it setup and working but it works really well.  Two things I had to do were first go into the settings of SHORTCUTS and turn on allow untrusted shortcuts and then I had to setup a dummy trusted shortcut before it would allow any untrusted shortcuts to be add.  then i went in and deleted that shortcut once I had everything working.

Let us know how it works for you.

I take no credit for this.  Someone who is much smarter than me developed this:

It is an APP problem that other uses are also experiencing.  If you have an Apple device there is a way to setup shortcuts to use voice controls or you can use the shortcuts themselves which I have found to be much faster than actually having to open the FordPass APP.

Let us know how it shakes out.

Technology evolves and changes.  There will be no winning lawsuit.

Yup that is the VSS or Vehicle Secirity System that has a built in shock sensor.  It only allows remote start if there is an antenna plugged into it (should be mounted on the windshield) and then a seperate remote start only fob is used.  So you would have two fobs, the remote start and the oem keyless.

https://accessories.ford.com/vehicles/edge/2017.html?cat=391

To follow up on what I said the service manual says this when replacing the front camera: "Follow the instructions on the scan tool to configure the front parking aid camera."

To be perfectly honest, that is rather vague and there is nothing that jumps out in IDS (thats the scan tool/software/computer the dealer uses) as something to configure the front camera so I could easiliy see this step being skipped over.  

When the camera is replaced though a procedure called LIN Module Initialization needs to be done.  This is under the diagnosis section for the front camera not being configured:

I wonder if they failed to progam the camera.

What module did you find under the dash?  Gotta know the hardware you have first.

16 hours ago, lil edgy said:

just bought an 2020 edge sel yesterday, woke up this morning and had condensation in the right tail light, salesman said the have vents in them, i think BS

It's not BS, they are made that way.  It is covered in your owner's manual.  

GENERAL INFORMATION

Condensation in the Exterior Front Lamps and Rear Lamps Exterior front lamps and rear lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions.

Examples of acceptable condensation are: • The presence of a fine mist (no streaks, drip marks or large droplets). • A fine mist covers less than 50% of the lens.

Examples of unacceptable condensation are: • A water puddle inside the lamp. • Streaks, drip marks or large droplets present on the interior of the lens. 

If you see any unacceptable condensation, have your vehicle checked by an authorized dealer.

54 minutes ago, krztfr said:

DaMiFo,

Thank you for taking the time to respond.   I can get it apart, so I can buy a replacement, and the only thing I am not sure I understand is the flashing of the cars AsBuilt data on to the unit with FORScan.  I will look that up and see where it will take me. 

Shame I can't trust my local Ford Dealers.  Thanks again for the help.  Best regards!

I can provide you with an up to date unit that is the proper one programmed for your car through the official dealer process.  Send me a message if you are interested.

The bi directional remote start utilizes the VSS module which is an add on post factory module that gets mounted under the dash usually in the area above the brake/gas pedal.  Sounds to me like you have the standard antenna which plugs into the TPMS in the rear cargo area and that is one directional for use with the IKT's (original style key fobs).

5 hours ago, Tad0216 said:

No everything comes on as it should but when I go to start the vehicle nothing happens. But it’s weird because it started working this morning with no problem

I don't have access to the service manual right now but the transmission may have a sensor/switch on it that senses if it is in park or not and will not start if the switch faulty.  Just a thought. 

@Tad0216 are you saying no electronics turn on as in the cluster doesn't come to life, the radio doesn't work or are you saying that all comes on but it just doesn't engage the starter?  Just asking for a little more clarification.

you need two keys that can start the car...does not matter if they have the fob built in or not.

WiFi wireless updating works with the vehicle off.  You don't need to sit there and watch it and wait.  Just FYI.

I hope they have given you a loaner that is nicer than your Edge.  I don't blame you for being upset.  I'd be curious to look up the OASIS SYNC history, sent me your VIN in a PM if you don't mind.

Still don't have it back?  Did Ford send someone to look at it yet?

11 hours ago, Guest 2007 ford edge said:

My 2007 doesnt have the large display screen. Can i still get my heated seats to come on with remote start?

Doubtful...your vehicle electrical architecture is an old generation.  Unless you use an aftermarket method.

Its not something a normal dealer tech would have the knowledge to do nor something Ford would ever authorize.  Downgrading is not an acceptable fix for them.