Jump to content

Rear caliper wont retract


Recommended Posts

On my 2016, it's not compressed, it needs to be turned to get the piston back in. Believe that there's a special tool that will make your life easier. Looks like a cube with different extensions on it to fit in the piston & ratchet it back.

https://shop.advanceautoparts.com/p/lisle-disc-brake-piston-tool-28600/25961363-p?product_channel=local&store=6997&adtype=pla&product_channel=local&store_code=6997&gclsrc=aw.ds&&gclid=EAIaIQobChMI9M240eiD7wIV1YtaBR0DgQ6wEAQYASABEgJkYPD_BwE

Edited by lildisco
  • Like 2
Link to comment
Share on other sites

On 2/24/2021 at 7:09 PM, fordedgenashvilletennessee said:

I have a 2015 Edge with the EPS. I am trying to change my rear pads. I can not get the left caliper piston to retract, even with the EPS maintenance mode. I have put it in maintenance mode and used a C clamp and a brake compressor tool and it is rock hard and won't go back in. Any suggestions?

Was lildisco   suggestions any help?

Link to comment
Share on other sites

  • 5 years later...

So, those of you who have done the rear brakes ... what tool did you use for the electric parking brake calipers?   Used the C clamp on the fronts.   Put car in brake service mode, removed the caliper ... but the cheap tool I bought to screw in the brake piston would not budge the piston.   Thinking I need to rent a tool?    What did you guys do?

 

Link to comment
Share on other sites

So, I just ordered another tool but I learned that some pistons (rear with electric parking) are right hand threaded and some are left hand threaded.  Anyone know which it is for a 2015 SEL?   I don't want to crank on it in the wrong direction.   Thanks. -D

Link to comment
Share on other sites

If service mode is actually activated, that means the electronic parking brake actuator is not engaged, you just need to compress the pistons in, like with that same C clamp you used on the front. Only time you might need to rotate it clockwise (either side, same direction) is if it won't compress enough to be fully compressed/you can't install the caliper with new pads over a new rotor.

Link to comment
Share on other sites

Did not want to hijack a similar thread ... same topic but different model year Edge.

 

I have a 2015 SEL3.5L FWD.   Replacing pads with OEM.  Fronts fit fine.  Rears are way too thick.  The caliper won't fit over them.   Pads are too thick.   

 

I ...

- put rear brakes in service mode

- used a rear brake piston compression tool for electric parking brakes ... worked perfect ... piston is left hand threaded BTW

- bought Motorcraft BRF-1474 pads

- verified fitment with the online Ford parts store

- bought hardware kit too

 

I just looked online and a different online store says to use part DG92-2200

 

Anybody know what the correct pads might be for this 2015 ?   Getting tired of pulling it apart only to find a problem in stalling new pads.

 

Thanks!

Link to comment
Share on other sites

BRF1474 is the same as DG9Z2200F.

 

Did you put in your VIN in the FordParts site, or just manually enter in your vehicle specs? There is a part year (maybe earlier than 1/19/2015 build date) change that maybe they are different.

 

I had to compress my rear pistons again after a couple of minutes because they started popping out before I could get it assembled. How flush is it after you have compressed them? Did you also replace the rotors? A ridge on old rotors might make it harder than the full thickness of new rotors. 

  • Like 1
Link to comment
Share on other sites

On 3/2/2021 at 5:59 PM, 1004ron said:

Was lildisco   suggestions any help?

My rear brakes are rock solid in service mode till I turn the piston just a bit.   I've only played with the right side ... and this side is left hand threaded ... so you turn it counter clockwise to loosen it up.   Then it seems fairly easy to turn and compress.   My problem is that I cannot get it compressed enough to fit over the new brake pads.   I need about 1/8 an inch.   I am going to try again.  This time I will be more careful to constantly turn it as it compresses.   Fingers crossed.

Link to comment
Share on other sites

  • 1004ron changed the title to Rear caliper wont retract

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...